Home Archery Boating Camping & Hiking Canoeing & Kayaking Climbing  
  What are you shopping for?  



 

Kreg RAC Right Angle Clamp

Kreg RAC Right Angle Clamp
MSRP: $24.99
Your Price: $24.92
Savings: $ 0.07 ( 0% )
Shipping: N/A
Manufacturer: Kreg
Buy Kreg RAC Right Angle Clamp

Prices subject to change. Please verify price during checkout.
 

Kreg RAC Right Angle Clamp Features

Securely holds work pieces at a 90 degree angle
Two arms swivel to adjust to work piece dimensions and anchor work pieces
4-1/2 inch reach for added flexibility
Easy release handle simplifies operation
 

Accessories for your Kreg RAC Right Angle Clamp

Kreg SK02 Pocket Hole Screw Kit
Fine Woodworking
Woodworking Basics: Mastering the Essentials of Craftsmanship
Kreg DDS 3-Inch No.2 Square Driver Bit and 6-Inch No.2 Square Driver Bit for Kreg Pocket Hole Systems
Kreg V07-DVD The Pocket Hole Solution to Trim Carpentry
 

Related Kreg RAC Right Angle Clamp Products

Right Clamp RAC Kreg Angle
Clamp Kreg Angle Right RAC
Angle Right RAC Clamp Kreg
Clamp Kreg Angle RAC Right
Clamp Right RAC Angle Kreg
Right RAC Kreg Angle Clamp
 

Additional Kreg RAC Right Angle Clamp Information

Large face clamp reaches up to 6" and ensures a perfectly flush joint every time! Large pad keeps clamp from marring wood. Perfect for flat stock such as face frames, mitered picture frames and other similar joints.

 

What Customers Say About Kreg RAC Right Angle Clamp:

Also this company is good to do business with. This clamp is a must to get good tight joints that stay at 90 degrees. Prompt shipment and arrived as stated.

It is easy and precise to use. It does an excellent job of pulling right angle joints together before installing the screws. The Kreg Right Angle Clamp is an essential tool for someone doing a full range of pocket hole joinery. The rubber coated handles provide good and comfortable grip.

Its a simple tool and does its job. It is helpful for clamping pieces of wood together when you are joining wood for pocket holes or even for gluing.

On advice from others I bought two for constructing a bath vanity. Well worth the investment. They held the plywood panels together very snugly to counteract the Kreg screws tendency to pull a panel slightly inward.

Trust your own judgement, though, go to a demo at a woodworking show or store and try them. Try THAT with a corner clamp. Conceptually, it's very simple. By the way, you can use these to clamp items that are not flush to one another, e.g., frame reveals, parts with differing thicknesses, and inset panels. As to the review that talks about blowing out the pocket hole, the only things that could possibly cause that are drilling too small a pocket (the clamps work perfectly with Kreg drills), clamping so tight as to crush the pocket, or clamping at an extreme angle (the clamp will work at a range of angles, not just 90 degrees). Or perhaps the owner has a defective clamp. It replaces one of the flats on a normal Kreg clamp with a pin that fits in the pocket hole. If you need 100% square accuracy, you can hold a square in place against the joint while you drive the screw.

To the reviewer that wondered about using pocket holes on the outside of items: In cabinet making, it's the INSIDE of the cabinet that's the concern. In any event, this is a highly unusual complaint, and I've yet to hear from anyone else with this problem. This clamp works flawlessly every time. Use the clamps in one or more pocket holes while you drive the screws into the others. The ply or particleboard sides and back of the cabinet are completely hidden for most cabinets and virtually always covered on end cabinets.

Buy Kreg RAC Right Angle Clamp
© 2006 - 2010 AlphaeBiz.com - Sporting Goods : Privacy Policy